Paracord Wrapping a Knife Handle - The Good Survivalist

useful skills

How to to upgrade your gear and equipment and learn cool ways to improve life & save money →

Prepress TRICKS

How to prepare yourself & your family for the worst

How To Build Stuff

Guides & Methods for DIY Projects

Paracord Wrapping a Knife Handle

The Method of the day for Survivalists:

T/h  | license

When I make a knife, I usually use micarta or wood for a handle, but sometimes I’ll do a cord wrap.

When people think of a cord wrapped handle they usually think of a single color wrapped circularly around the handle, BORING!

So I decided to come up with a good way of mixing two colors for a wrap, this is the second knife I’ve made with this method, the first one was black and glow in the dark paracord. I was sitting in front of the tv, a knife in one hand, and some glowing and some black paracord in the other, I started messing around, and this wrap is what I came up with.

Hope you like it.

Step 1: Supplies

Picture of Supplies

You need:


paracord (2 colors)


multi-tool (or you can just get pliers, pointy pokey thing, and a knife for cutting cord)

Step 2: Cut and Gut.

Picture of Cut and Gut.
Picture of Cut and Gut.

Cut the paracord into the needed lengths, I used 4′ of each color, just remember that it’s easier to cut off extra cord than it is to add cord.

Go ahead and gut the cord also, make sure any melted ends are trimmed and pull out the inner strands.

Step 3: Readying for Wrapping

Picture of Readying for Wrapping
Picture of Readying for Wrapping
Picture of Readying for Wrapping
Picture of Readying for Wrapping

Ducttape the blade (I hate cutting myself while wrapping a knife).

Push an inch or so worth of cord through the starting hole. This is where we need to think this through. Whichever side you put the strands on, it will create a bump on that side, so I always put them on the inner grip side of the handle. The inner side of the grip is the side where you fingers wrap around, not your palm. It’s more comfortable to hold it with the bump on the inner grip side, so I always put it there.

Did that make sense?

Okay, after you push the end of the cords through the starting hole, take a drop of superglue, and glue the ends of the cords down, this just helps keep them tidy and out of the way.  Just don’t superglue your fingers together.

Step 4: The Wrap

Picture of The Wrap
Picture of The Wrap
Picture of The Wrap
Picture of The Wrap

You know the first knot you do when you tie your shoes? This is the knot we’ll use.

Pull the cords around to the same side that the cord ends are on. Make sure the black goes under the orange, then pull it over the orange (just look at the pictures, I’m not really making sense here am I?).

Then you flip the knife over and do that knot on that side. Make sure you pull it tight. Then you just keep flipping and repeating.

Step 5: Entertainment

Picture of Entertainment

I like to watch a good tv show or something while doing wrapping. Just make sure your still paying attention to what your doing.

Step 6: Ending

Picture of Ending
Picture of Ending
Picture of Ending

When you get to the end hole, one cord will be right at the hole, one will be further away. In this case black was closest. Pull the closest cord through the hole right there, and pull the other one around and then through the hole. Tie a knot to end it, and do what you will with the rest. Typically I would end it by putting on a cool looking bead and knotting it again. But, I don’t have anything good on hand, so I just trimmed them at about 1″ long and left them there.

Step 7: Resin Coating

Picture of Resin Coating
Picture of Resin Coating
Picture of Resin Coating
Picture of Resin Coating

Take the now wrapped knife, and tape off most of the blade and any areas you don’t want resin on, you can typically pop the resin right off of bare steel, but might as well just tape it and save time.

Mix up a small amount of fiberglass resin, I used 1 oz, but 1/2 oz would have easily sufficed, I just couldn’t measure that small in my mixing cup.

Use a cheap (I repeat, cheap) paint brush and carefully brush resin all over the cord. Let it soak in, and brush on more as needed. Then carefully clamp in vise to cure.

After a few minutes, remove knife and turn it over, that way any resin gathering at the formerly bottom end, will not cure into drops or bumps on the side facing down (did that make sense?).

⚒ Freebies - Guides - Methods ⚒

📭 Emails I sent with methods & tips:

More from the blog

Like it? Share with your friends!


Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.